1. 帮忙翻译一下弹簧扳道器说明书
SL-120 type of flexible railway switch
Manual
A summary
1. SL-120 type of flexible railway switch (Abbreviations: railway switch) is a manual switch turnout equipment.
2. To its spring tension to achieve the turnout to be anti-bit conversion, and will be maintained at its anti-bit capability.
3. Easily apply to "squeeze bifurcated fault" circumstances turnout, once crowded bifurcated not damaged equipment.
4. Lock will be on the base axis of penetration and the locking hole with padlock to lock in turnout for anti-bit state to facilitate a bifurcated traffic safety.
The proct features
1. Handle length scalable 290 MM, when the turnout conversion little resistance, length can be shortened handle the contrary, the extension handle length.
2. Handle扳动itinerary for the decrease, to handle the rotating 180 degrees to facilitate human operator.
3 above telescopic handle with rotating the casing by spring sales of the two filed, after falling into the adjustment to achieve.
4. To overcome扳动resistance, the controller design for the core head slider structure, its structure扳动flexible.
5. Rectangular Shui rotating spindle center, equipped with roller bearing, raising proct life and accuracy.
6. Where rotation axis between holes, are equipped with a self-lubricating properties of materials bush.
7. Rod connected with the turnout, using the fine-tuning, in the use after the installation process, not dismantle its connecting pin, the turnout openings can be posted and the state of adjustment.
Three technical parameters
1. Apply ≤ 120 mm openings Turnout
2. Applicable conversion turnout resistance ≤ 1960 N (200KG)
3. Rod largest linear displacement of 209 mm
4. Installation of the two枕木center distance 650 mm, with the rod tip Department枕木two bifurcated centerline distance of 350 mm
5. Installation of the double-track railway lines in the middle, adjustable handle from the center line on both sides should be ≥ 22.5 mm
Principle and the installation of four structural adjustment (see the installation diagram)
1. Gauge before installation, inspection, the turnout laying parameters枕木placed spacing is consistent with the relevant technical standards.
2. Installed before use撬棍respectively拨动two apical orbit so close affixed to the basic track-inspection bifurcated Tsim and刨切paragraph of whether the stickers, a non-bifurcated sharp gap best,刨切of the gap should not be large at 1 mm.
3. Angle steel structure will be the installation of devices, one end with 22 mm × 145 mm solid wood screw道钉pinch points in turnout traction on both sides of the wooden pillow-head, the other side needs in line, the laying of a wooden pillow, in the same pinch solid wood枕上.
4. Rod side and right-angle Shui, for fine-tuning the other side of the bar association and the turnout connected together.
5. When railway switch device with the turnout has been fixed link integrity, the first to tie the handle perpendicular to the center position, that is a right angle Shui are also at the middle position; began to adjust the fine-tuning the entire rod, the two apical track for turnouts respectively with straight, curly basically the same size opening track. Turnout orifice size should be open for one half, that is, 60 mm.
6. Completed on the basis of the above adjustments, the first pull to handle one end, a sharp track and check whether the basic track of stickers, if space, use fine-tuning device to be corrected if there is still space, adjusting the compression spring nut to increase Spring tension until the secret stickers. Then handle pull to one end, the same method used to adjust the above, also reached the other side of stickers.
7. In the following two circumstances, the handle can be shortened length.
(1) When converting Turnout little resistance when human can扳动
(2) when the turnout in the set, anti-places, for reced vertical height handle
Whether or shrinkage handle extended its length, method of operation, has filed handle casing on two spring sales and rotating 90 degrees, casing from the connecting rod and handle the role, can hold length adjustment. And then rotated 90 degrees so that the spring-pin inserted into the hole in the handle and restore connectivity role.
8. Handle railway switch to rece the itinerary to facilitate human operators, to handle the curved shape. So pull from one end to one end, according to the length of the methods of operation telescopic handle, to be rotating 180 degrees for the next扳动facilitated.
9. Structure for the railway switch principle is: rotating through rectangular Shui can be certain angle to the rectangular Shui一臂can handle拨动, and the other arm with a certain tension on the composition of the spring. Tension role in the spring, according to Cartesian Shui not stagnation in the middle of the principle, in tension with a spring rod arm hang, in a Cartesian Shui rotation angle are the two ends have some traction, providing impetus to the conversion Turnout .
Five Maintenance
1. Use of the ministries should be guaranteed complete fasteners, bolts fastening, opening a sales arm angle to prevent loss provisions.
2. Connecting pin in the hole should wear Kuang of not more than 1 mm, excessive Kuang be timely replacement of connecting pin.
3. Should ensure that the turnout conversion process, the ministries movements smooth, rotating flexible, non-card resistance phenomenon.
4. Pin and Hole, the first with the slider handle inter should regularly coated surface oil, and maintain lubrication good.
2. 道岔是不是必须要有扳道器
首先，题目问得有问题，扳道器是众多道岔转辙设备中的一种，应该问道岔是否必须应配置道岔转辙设备，这是必须要有的，否则就失去了设置道岔的目的；其次，只有人工扳道的道岔才使用扳道器，现在早已进入电气化铁路采用信号控制的时代了，扳道器已在正线线路彻底退出了。
3. 扳道器是怎么工作的
道岔有手动、电动和气动等不同的扳动方式。用手扳动一副道岔也要有力气和技巧。如果你坐火车在晚上经过车站，看到星星点点黄色或紫色灯光是手动道岔所在地的标志。白天，看到的则是一块黄底黑条的鱼尾板。电动或气动岔则可以集中在控制台上进行操纵。电动或气动道岔的转动速度很快，又可以集中控制，对提高铁路运输效率具有很大的意义。除了单开、双开、三开这样的正宗道岔之外，还有垂直交*、菱形交*、交*波线、复式交分等道岔的组合或变种。在最小的仅有两股道的会让站，也有近十个道岔。至于大型的编组站，备种道岔星罗棋布，数以千计。因此，必须在现场将道岔一一编上序号，让它们井然有序地动作，保证列车畅通无阻都能走对道。
以上来自网络，希望可以帮你
4. 安装扳道器时应注意哪些
①电气设备的安装与电缆敷设应安设在顶板无淋水和底板无积水的地方，应不妨碍人员通行，距轨道和钢丝绳应大于等于600mm的距离，避免影响运输车辆运行。
②电缆应使用电缆钩悬挂，严禁用铁线悬挂。
③橡套电缆之间的直接连接必须采用冷压、冷补工艺。
④用人力敷设电缆时，应将电缆顺直，在巷道拐弯处不能过紧。人员应在电缆外侧搬运，电缆悬挂的间距为1.2m。
⑤工作面与顺槽拐角处的电缆要吊挂牢固，禁止在上三角区吊挂电缆。
⑥搬运电气设备时，要绑扎牢固，禁止超宽超高。要听从现场负责人指挥，防止碰人和损坏电气设备。
⑦严禁带电搬运电气设备和缆线。
5. 战争的真相德军第二幕滴5关要怎样扳动火车扳道器而不被发现。
把那个扳道器跟前的兵杀了就可以了，不要被其他的巡逻兵发现就行。
6. 扳道器是什么它有哪些种类zmjt15
扳道器产品简介zmjt15
扳道器按工作方式不同分为手动卧式扳道器,手动弹簧扳道器,手动立式扳道器,根据工作要求又分为手动扳道器和电动扳道器两种。
扳道器以弹簧的张力来实现道岔转换到定反位,并将其保持在定反位的功能。
扳道器适用于容易发生“挤岔故障”情况下的道岔,一旦挤岔不会损坏设备。
扳道器可以锁闭轴内穿入底座上的锁闭孔内并加上锁头,使道岔锁定在定反位状态,以利于行车过岔安全。
扳道器按工作方式不同分为手动卧式扳道器,手动弹簧扳道器,手动立式扳道器,根据工作要求又分为手动扳道器和电动扳道器两种。